![]() ![]() It’s measured in milliseconds (ms), and the lower the ping number, the better. Ping, also known as latency, is a measure of the round-trip time for data packets sent from one computer to a website or game’s server and back again. What Is Ping and Why Is It Important in CS:GO? Just take a break and come back when you’re ready. In the meantime, try not to let the high ping get to you. First, I want to talk about what ping is and why it matters. In this blog post, I’ll teach you how to lower your ping in CS:GO. Luckily, you can lower your ping and get back to playing the game you love. Don’t even get me started on the times when you end up getting killed because of it. Every time you move, your character lags behind other players, making it hard to aim and shoot accurately. This means that R1 doesn’t know how to reach the 192.168.5.0/24 network.There’s nothing more frustrating than trying to play a game of CS:GO with high ping. In the output above you can see that no echo replies were received after I changed the source IP of the ping packets. ![]() Packet sent with a source address of 192.168.5.1 Loose, Strict, Record, Timestamp, Verbose: This is done to ensure that R1 knows about the 192.168.5.1 network (in other words, that it knows where to send packets destined for the 192.168.5.0/24 network, which could indicate routing problems). However, I can run the extended ping command to change the source IP address to the IP address of the R2 Fa0/0 interface (192.168.5.1). Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/1 msĪs you can see from the output, the ICMP replies were received. Sending 5, 100-byte ICMP Echos to 10.0.0.2, timeout is 2 seconds: Let’s try to ping R1 using the standard ping command: R2#ping 10.0.0.2 This means that R2 will use the IP address of the Fa0/1 interface (10.0.0.1) as the source IP address for the ping packets sent to 10.0.0.2 (R1). Consider the following example:īy default, routers choose the IP address of the outgoing interface as the source IP address for ping echo packets. The extended ping command is most often used to change the source IP address of the ping echo packets. This parameter is used to determine the minimum sizes of the MTUs configured on the nodes along the path to the destination address. Sweep range of sizes – specify the sizes of the ping echo packets that are sent.Loose, Strict, Record, Timestamp, Verbose – specify the IP header options.Data patterns are used to troubleshoot framing errors and clocking problems on serial lines. Data pattern – specify the data pattern.Validate reply data? – specify whether or not to validate the reply data.If yes is entered, the Don’t Fragment option does not allow the packet to be fragmented. Set DF bit in IP header? – specify whether or not the Don’t Fragment (DF) bit will be set on the ping packet.This is the Internet service’s quality selection. Type of service – specifies the Type of Service (ToS).Source address or interface – specify the interface or the IP address of the router to use as the source address for the ping packets.If you type yes additional arguments will be shown. Extended commands – specify whether or not a series of additional commands will appear.The echo reply needs to be received before the timeout expires in order for ping to be successful. Timeout in seconds – specify the timeout interval.Datagram size – specify the size of the ping packet (in bytes).Repeat count – specify the number of ping packets that will be sent to the destination address.Target IP address – specify the IP address or the hostname of the host to ping. ![]() Protocol – specify the protocol, such as appletalk, clns, ip, novell, apollo, vines, decnet, or xns.The extended ping command is invoked from the privileged exec mode by typing ping and pressing Enter. With this command, you can define the source IP address as any IP address on the router, number and size of ping packets, different timeout interval, etc. ![]() Cisco devices also support the extended ping command that allows you to perform a more advanced check of the host reachability and network connectivity. The ping command in Cisco IOS (and other operating systems) is used to test the accessibility of devices on a TCP/IP network. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |